How Tall Are The Pedestals?
Samsung pedestals are 15 inches tall.
Where Are The Vent knockouts Located On My Dryer?
If you are going to side vent your dryer, the vent knockouts are located 7 from the rear of the cabinet and 4 from the bottom of the cabinet on either side. (Measurements Are to The Center Of The Knockout) The Bottom vent knockout is located 15 from the right side, 12 from the left side,
How Do I Mount The Drying Rack?
Mounting the Drying Rack Open the door. Mount Drying Rack in tumbler by engaging the two rear tails into the two recessed areas in the back wall. Place the front tail of Drying Rack on top of the lint filter. Place items to dry on the rack, giving enough space between them to give more air
Why Is My Dryer Drying Unevenly?
If your dryer isn’t drying evenly: Seams, pockets, and other similar heavy areas may not be completely dry when the rest of the load has reached the selected dryness level. This is normal. Select the Very Dry setting if desired. If one heavy item is dried with a lightweight load, such as one
The Clothes Are Wrinkled.
[Solution] To reduce wrinkling, please refer to the followings: The Samsung dryers have the “Wrinkle Prevent” cycle. The “Wrinkle Prevent” provides approximately 90 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Press the “Wrinkle Prevent”
Dryer Does Not Power Off At The End Of A Cycle
Your dryer does not automatically power off at the end of a cycle. This is normal.
What Is Sensor Dry?
Sensor dry automatically senses the moisture in the load, and shuts the dryer off when the selected dryness level (very dry to damp dry) is reached.
The Display Is Showing An Hour Glass
If your dryer is showing an hour glass on the display, it is normal. The hour glass is there to let you know that there is a cycle in progress.
Child Lock / Controls Will Not Respond
If your dryer controls will not respond, the Child Lock Function may be on. To activate / deactivate the child lock function, on most models, press and hold the Time and Signal buttons simultaneously for 3 seconds. On other models, press and hold the Temp. and Time buttons simultaneously for
How To Reverse The Dryer Door
To reverse the dryer door, perform the following steps: Note: A Phillips Head Screwdriver is required for this procedure. Open the dryer door and remove the 4 screws around the latch on the door frame. Then, remove the door latch. Next, remove the 2 large screws on the door
Dryer Troubleshooting: Does Not Run
If your Samsung Dryer will not run, try these tips to troubleshoot the issue.
Unpleasant Odor From Dryer
There are very few things that can cause unpleasant odors from your dryer. Below is a list of the top 3 reasons for the odor. The lint trap has not been cleaned. If the lint trap is not cleaned it can block moisture from escaping from the drum and the air inside is recycled, through the old
Dryer Will Not Power On
If your dryer does not power on, check the following: Warning: Electrical repairs should be preformed by a licensed electrician. Note: Samsung electric dryers requires a dedicated 30 ampere circuit, and gas dryers require a dedicated 15 ampere circuit. Make sure your dryer is plugged in.
Clothes Are Damp At The End Of A Dry Cycle
Important: If you are having issues on a Sensor Dry cycle and using dryer sheets, wipe off the sensor. It is located inside of the drum below the lint filter housing. A film or residue can build up on the sensor preventing it from sensing accurate moisture levels. Use a lint free cloth with a
Temperatures For Heat Settings
These are the approximate temperature settings for each heat cycle Extra Low: 100 - 110° (F) Low: 120° (F) Medium: 130° (F) High: 140° (F) Below are pictures of the various heat cycle selections
What Are The Ducting Requirements For My Samsung Dryer?
Warning: Do not exhaust dryer into any wall, ceiling, crawl space, or concealed space of a building, gas vent, or any other common duct or chimney. This could create a Fire Hazard from lint expelled by the dryer. Ducting Requirements: Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid
Electric Dryers require a 240-Volt power supply (for more information about a 240-Volt outlet, see 240-Volt Outlet below): Dedicated 30 Ampere circuit breaker is required. 60 Hz AC approved electrical service is required. Note: A 208-Volt outlet is insufficient to power our electric
Important: Always follow the use and care instructions on the label of the fabric being dried to avoid damage and shrinking to the material. Additionally, use the Fabric Care Chart in the User Manual as reference for drying the materials in the dryer. If you would like to download a copy of
Child Lock - When lit, the control panel is disabled. Delay Start - When lit the unit has been programmed to start after a set amount of time has passed. Lint Trap - When lit, this icon lets you know to check/clean the lint trap. Mixed Load - When lit, the laundry in the dryer is a mix
Important: Physical damage is not covered under warranty. Physical damage includes, but is not limited to: cracks, scratches, corroded, rusted, peeled, deformed, and discolored parts, and accessories. If your dryer has physical damage, we will be happy to repair or fix it, but the repair will
Other Online Resources
If you can not find an answer to your problem in the Troubleshooting Guide, call Samsung Customer Care for additional help. For additional on-line help click the links below: Click here to go to the Samsung Download Center page. Click here to go to Customer Service for Samsung Online Orders.
Not Able To Use A Different Style Of Lint Trap
Samsung dryers have a couple of different styles of lint traps. Some have asked if the different styles are interchangeable from unit to unit. The answer is no, they are not. The lint trap and lint trap housing, while they look like similar, are actually quite different. The lint trap with the
Discolored Marks On The Vent Inside The Drum
This is normal. The discoloration on the vent comes from the constant heat in that area, because the heater is located directly below that vent. This is the hottest part of the drum. img1.gif
Excessive Drying Times While Using Sensor Dry
If drying times are extremely long while using Sensor Dry, verify/perform the following: Avoid drying mixed load with fabrics that have various densities. If you use dryer sheets/fabric softener sheets, clean the sensor bars with lint-free cloth and rubbing alcohol. Do this by putting a
Wrinkle Prevent / The Display Shows A Scrolling Rectangle
A customer may complain about seeing a scrolling rectangle or a forward C, two lines, and a backwards C on their dryer's display. This is NOT an error code. Nothing is wrong with their machine. This display simply indicates that their machine is running a wrinkle prevent cycle.