How to use Wireless PowerShare

Wireless PowerShare lets you charge your device using another Qi enabled device, without the need for a charger. You can also charge two devices at the same time using just one charger.

Wireless PowerShare

Devices that support Wireless PowerShareClick to Expand

Wireless PowerShare is supported by all WPC Qi certified smartphones and Samsung wearable devices.

 

  • Smartphones: A Samsung or another branded smartphone that supports wireless charging (WPC Qi-certified devices). Different devices may charge at different speeds.  Other branded smartphones can vary depending on the device setting or design, even for WPC Qi certified devices.
  • Wearable devices: Samsung wearable devices only (Gear S3/Sport, Galaxy Watch, Galaxy Watch Active, Galaxy Watch Active 2, Galaxy Buds).
How to use Wireless PowerShareClick to Expand

If the battery on your device is getting low, use Wireless PowerShare to charge your device using another compatible device.

1 Swipe down from the top of the screen to reveal the notification panel, then tap "Wireless PowerShare" to activate. A blue flashing light appears on the back of your device when Wireless PowerShare is activated.
Swipe down from the top of the screen to reveal the notification panel
2 Place the devices with their backs facing one another.

Please note: The location of the charging coil may vary by device model. You may need to adjust the devices until they connect with each other properly.

Galaxy devices charging via Wireless PowerShare
3 The screen will confirm once the devices are connected. Tap “OK”. The light on the back of the device will turn red while charging.

If you pull down the notification panel again a message will show that it is charging the connected device. The green Wireless PowerShare icon will also appear on the display bar or on your Always On Display panel.

Please note: If the battery level on your device drops below a certain level, Wireless PowerShare will automatically turn off.

4 Once the device is fully charged, the light will turn off. Separate the devices when enough power has been transferred or wait until the other device is fully charged.

Watch our video on how to use Wireless PowerShare:

Video Alternative Text
Dual chargingClick to Expand

You can also use Wireless PowerShare to charge a second device while your device is plugged in to a wired charger. This way, both devices will charge at the same time and you only use one charger. Follow the same steps as in the "How to use Wireless PowerShare" section above while one of your devices is plugged in.

Use Wireless PowerShare to charge another device while charging via a cable
Why is Wireless PowerShare not working properly?Click to Expand
1 Check device compatibility.

Wireless PowerShare is supported by all WPC Qi certified smartphones and Samsung wearable devices. Check to make sure that both devices are compatible with the feature.

Please note: Not all devices with wireless charging capability are compatible with Wireless PowerShare.

2 Activate Wireless PowerShare.

Swipe down from the top of the screen with two fingers to access the Notification panel. Then, tap the Wireless Powershare icon to activate.

3 Check battery level.

The phone that is providing the power needs to have sufficient charge in order for Wireless PowerShare to work. If the phone sharing power has less than 30% battery remaining and is not plugged in, Wireless PowerShare will not turn on.

4 Remove case or cover.

Depending on the type of accessories or cover being used on your device, the Wireless PowerShare feature may not work properly. It is recommended to remove any accessories and protective phone covers before using this feature.

5 Clean surface of devices.

Check that the backs of the devices are free from dust, dirt or moisture before using Wireless PowerShare.

6 Reposition devices.

Place the devices on a flat surface with plenty of space.

The efficiency of wireless charging depends on the distance between the charging coils embedded in the devices. You may need to adjust the position of the devices until they connect with each other properly.

Because the position of the wireless charging coils can vary by device, you may need to slowly move the devices until they are in the correct position. When charging starts, the PowerShare phone will vibrate and play a tone.

The below image shows the position of the embedded wireless charging coils. In this example we have used the three Galaxy S10 models.

Wireless PowerShare coil location on Galaxy S10 series

Please note: If you are using a Galaxy Fold, please close the phone before starting Wireless PowerShare. Read our FAQ to find more about how to use Wireless PowerShare on the Galaxy Fold 5G.

Thank you for your feedback!

Not finding what you're looking for? We're here to help.

Online

Twitter

Tweet us | 9am-9pm, 7 days a week

Facebook Messenger

We are here to help | 9am-9pm, 7 days a week

Live Chat

Smartphone support | Mon-Sun | 8am to 8pm
All Products support | Mon-Sun | 8am to 8pm

Order Status & Tracking

Send us an email to get an update on your Samsung Shop order.

Track my repair

Check the status of your repair with Samsung

SmartThings Support

Help with Hubs, Kits, Sensor and Outlets

Call

0818 717100Phone Support

Smartphone support | Mon-Sun | 8am to 8pm
All Products support | Mon-Sun | 8am to 8pm

0818 302 016Samsung Shop

For new and existing orders | 9am - 5pm, 5 days a week

0124 75161B2B Support

For business support
8am - 6pm, Mon - Fri

Calls to 0818 numbers are a National Call number.
These are subject to call charges which vary by network and are subject to change.
Calls maybe recorded for training and quality purposes.
For information on how we collect and use your details, please refer to our Privacy policy

* For any printer related enquiries please visit the HP website.

Face-to-face support

Samsung Support Centres

Find out more about how you can get face to face help.

Contact Us